CLASSIFICATION |
AWS: A5.18 |
IS : 6419 |
ER : 70S - 6 |
C 503 X GRADE S4 |
IDENTIFICATION :
STICKER CURRENT CONDITION
DC(+)
Approved and Certified by:
Chief Inspector of Boilers (IBR), Indian Register of Shipping, BHELTrichy
Characteristics:
A copper coated solid wire having highest combination of Mn and Si. It permits high current welding with carbon dioxide gas shielding even in rimmed steel. Smooth flow with stable arc and minimum spatter and its special characteristics. This may be used to weld sheet metal where smooth weld beads are desired.
Typical Applications:
Suitable for welding of Mild Steel, Carbon Steel and low alloy steel including structural steel with tensile strength upto 590 N/mm2.
Weld Chemistry: (%) (All single values are maximum) |
|||
| C | 0.07 - 0.15 | Mn | 1.40-1.85 |
| Si | 0.80 - 1.15 | P | 0.025 |
| S | 0.025 | Cu (including coating) | 0.5 |
All Weld Mechanical Properties: (All single values are minimum) |
|||
| YS | 420 N/mm2 | El% | (5.65 √A) 22% |
| UTS | 560 N/mm2 | Impact CVN | 27 J at - 29°C |
| Available size | : | DIA:0.80mm/1.0mm/1.2mm/1.6mm (Continuous) 1.6,2.0,2.5,3.15 (Cut length of one meter) |
| Shield Gas | : | CO2 or CO2 + Ar |
| Net Weight wire | : | 12.50 to 15.00 Kgs per Spool |
| Precaution | : | To be stored in dry place. |
CLASSIFICATION |
AWS: A5.18 |
ER : 70SG |
IDENTIFICATION :
STICKER CURRENT CONDITION
DC(+)
Characteristics:
Solid wire for MIG MAG welding of mild steel and high tensile steel in all positions. While welding on thick plate, it can provide higher deposition efficiency with less fume and good bead appearance. Widely used in buildings & Bridges, heavy vehicles etc.
Typical Applications:
Suitable for welding of Mild Steel, Carbon Steel, and low alloy steel including structural steel with high tensile strength upto 590 N/mm.
Weld Chemistry: (%) (All single values are maximum) |
|||
| C | 0.07 - 0.15 | Mn | 1.80 |
| Si | 0.80 - 1.15 | P | 0.025 |
| S | 0.025 | Cu (including coating) | 0.50 |
All Weld Mechanical Properties: (All single values are minimum) |
|||
| YS | 420 N/mm2 | El%(5.65 √A) | 22% |
| UTS | 560 N/mm | Impact CVN | 27 J at -29 C |
Current Range (Amps) |
|||
| 0.80mm | 1.00mm | 1.20mm | 1.60mm |
| 50-80 | 80-220 | 120-280 | 200-400 |
| Available size | : | DIA:0.80mm/1.0mm/1.2mm/1.6mm (Continuous) 1.6,2.0,2.5,3.15 (Cut length of one meter) |
| Shield Gas | : | CO2 |
| Net Weight wire | : | 12.50 to 15.00 Kgs per Spool |
| Precaution | : | To be stored in dry place. |
CLASSIFICATION |
AWS:A 5.28 |
ER - 80SG |
IDENTIFICATION : STICKER PASTED
CURRENT CONDITION DC (+)
Characteristics:
Solid wire for MIG MAG welding of mild steel and high tensile steel in all positions. While welding on thick plate, it can provide higher deposition efficiency with less fume and good bead appearance. Widely used in buildings & Bridges, heavy vehicles etc.
Typical Applications:
Suitable for welding of Mild Steel, Carbon Steel, and low alloy steel including structural steel with high tensile strength upto 590 N/mm2.
Weld Chemistry: (weld metal % ) |
|||
| C | 0.12 Max | Mn | 0.60 - 1.20 |
| Si | 0.25 – 0.70 | P | 0.03 Max |
| S | 0.03 Max | Cu | 0.25 – 0.65 |
| Ni | 0.30 – 0.80 | Cr | 0.20 – 0.70 |
All Weld Mechanical Properties: |
|||
| YS | 350 N/mm2 Min. | ||
| U.T.S. | 490 N/mm2 Min. | ||
| E% (5.65 √A) | 22% | ||
| CVN Impact | 50 J – 20°C | ||
Current Range (Amps) |
|||
| 1.20 mm | 1.60 mm | ||
| 120 - 180 | 150 – 375 | ||
| Available size | : | DIA: 1.2mm/1.6mm/2.0mm (Continuous) 1.6,2.0,2.5,3.15 (Cut Length of one Meter) |
| Welding Current | : | DC (+) |
| Shield Gas | : | CO2 |
| Net Weight wire | : | 12.50 tp 15 Kgs. Per Spool |
| Packing | : | Winding on plastic Spool, Sealed in polythene bag, then packed in corrugated box which is further sealed with shrink film. |
| Precaution | : | To be stored in dry place |
CLASSIFICATION |
AWS:A 5.28 |
ER - 90SD2 |
IDENTIFICATION : STICKER PASTED
CURRENT CONDITION DC (+)
Characteristics:
Solid wire for MIG MAG welding of mild steel and high tensile steel in all positions, producing radiographic weld metal with high tensile strength and impact resistivity. Used for producing weld metal with Mn – 0.50 Mo type.
Typical Applications:
Used for welding of High strength steels such as Gr 60, Gr 70, Gr 65 etc, Ideally used for Penstock welding, Railway chassis etc.
Weld Chemistry: (solid Wire % ) |
|||
| C | 0.07 – 0.12 | Mn | 1.60 - 2.10 |
| Si | 0.50 – 0.80 | S | 0.025 Max |
| P | 0.025 Max | Mo | 0.40 – 0.60 |
| Ni | 0.15 Max | Cu | 0.20 – 0.40 |
All Weld Mechanical Properties: |
|||
| YS | 450 N/mm2 Min. | ||
| U.T.S. | 590 N/mm2 Min. | ||
| E% (5.65 √A) | 20% | ||
| CVN Impact | 27 J - 20°C | ||
Current Range (Amps) |
|||
| 1.20 mm | 1.60 mm | ||
| 120-375 | 150-375 | ||
| Available size | : | DIA: 1.2mm/1.6mm/2.0mm (Continuous) 1.6,2.0,2.5,3.15 (Cut Length of one Meter |
| Welding Current | : | DC (+) |
| Shield Gas | : | ARGON/1% - 5%/ OXYGEN |
| Net Weight wire | : | 12.50 to 15.00 Kgs. Per Spool |
| Packing | : | Winding on plastic Spool, Sealed in polythene bag, then packed in corrugated box which is further sealed with shrink film. |
| Precaution | : | To be stored in dry place |
CLASSIFICATION |
AWS: A5.18 |
ER : 70S - 2 |
IDENTIFICATION :
STICKER CURRENT CONDITION
DC(+)
Characteristics:
PRIMA –MIG S2 is a solid wire for Mig & Tig welding, it is a triple deoxidized steel welding wire with very low impurities. Weld deposit is tough, ductile and of radiographic quality.
Typical Applications:
Suitable for NACE pipe- TYPE A106 Gr.B or equivalent grades, pressure vessels & boilers involving unalloyed and micro alloyed structural steels with specified tensile strength upto 520 MPa to meet subzero impact down to -46°C.
Weld Metal Chemistry (All single values are maximum) |
|||
| C | 0.07 | P | 0.025 |
| Mn | 0.90-1.40 | S | 0.035 |
| Mo | 0.15 | Ni | 0.15 |
| Cr | 0.15 | V | 0.03 |
| Si | 0.40-0.70 | Cu (including coating) | .50 |
All Weld Mechanical Properties: (All single values are minimum) |
|||
| YS | 420 N/mm2 | El% (50 MM GL) | 24% |
| UTS | 510 N/mm2 | Impact CVN | 60 J at - 0°C |
| Available size | : | DIA:0.80mm/1.0mm/1.2mm/1.6mm (Continuous) 1.6, 2.0, 2.5, 3.15 (Cut length of one meter) |
| Shield Gas | : | CO2 or Ar + CO2 |
| Net Weight wire | : | 12.50 to 15.00 Kgs per Spool |
| Precaution | : | To be stored in dry place. |
CLASSIFICATION |
AWS/A- 5.9 |
ER 410 Ni Mo |
IDENTIFICATION : STICKER PASTED
CURRENT CONDITION
DC(+)
Characteristics:
Solid welding wire ideal for welding of materials with similar composition in cast and wrought forms such as turbines, valve bodies etc Weld metal deposit consist of C12 Cr4 Ni 0.5Mo suitable to use with Ar-Co2 mix shielding gas.
Typical Applications:
Suitable for overlaying on mild and low alloy steels, welding AISI-410 and similar composition alloys. Turbines, valve bodies, Power generation and high pressure pipping, Chemical 7 Petrochemical inductry
|
Weld Chemistry: (%, single values are maximum) |
|||
| C | 0.06 | Mo | 0.40 – 0.70 |
| Mn | 0.60 | Ni | 4.00 – 5.00 |
| Si | 0.50 | Cr | 11.0 – 12.5 |
| S | 0.03 | Cu | 0.75 |
| P | 0.03 | ||
Current Range (Amps) |
|||
| 0.80 mm | 1.00 mm | 1.20 mm | 1.60 mm |
| 50-80 | 80-220 | 120-375 | 150-375 |
| Available size | : | DIA:0.80mm/1.0mm/1.2mm/1.6mm/2.0mm (Continuous) 1.6,2.0,2.5,3.15 (Cut Length of one Meter) |
| Welding Current | : | DC (+) |
| Shield Gas | : | ARGON. + OXYGEN OR ARGON |
| Net Weight wire | : | 12.5 |
| Precaution | : | Winding on plastic Spool, Sealed in polythene bag, then packed in corrugated box which is further sealed with shrink film. |
| Precaution | : | To be stored in dry place |